Effects of Water pH on the Stability of Pesticides
Department of Agronomy
The pH level of the water used in a pesticide spray mix influences the effectiveness of some pesticides. The term pH (potential of hydrogen) refers to a measure of the concentration of hydrogen ion (H+) and hydroxide ion (OH-) in a solution. If hydrogen predominates, the solution is acidic; if hydroxide predominates, the solution is basic, or alkaline.
A logarithmic scale of 0 to 14 is used to measure pH. A pH value of 7 indicates neutrality. Values below 7 indicate acidic conditions; pH values above 7 indicate alkaline conditions. Because a logarithmic scale is used in measuring pH, a pH of 6 is 10 times more acidic than a pH of 7, and a pH of 5 is 100 times more acidic than a pH of 7.
Some pesticides, particularly carbamate and organophosphate insecticides, undergo a chemical reaction in the presence of alkaline water (water that has a pH value greater than 7). The reaction is known as alkaline hydrolysis, and it reduces the effectiveness of the pesticide's active ingredient.
Depending on the specific chemical properties of the pesticide, the pH of the mix water and the length of time that the pesticide is in contact with the water, the breakdown can happen relatively rapidly. Spray-mix water with a pH value between 8 and 9 can cause a rapid hydrolysis to the point that the degree of pest control is greatly diminished or lost.
Chemical breakdown of a pesticide is commonly referred in terms of its half-life. A half-life is the period of time it takes for one-half of the amount of pesticide in the water to degrade. Each half-life that passes reduces the amount of pesticide present in the water by one-half; that is 1 to 1/2 to 1/4 to 1/8 to 1/16, etc. Table 1 summarizes the half-life of pesticides with varying pH values that are commonly used in Missouri.
Half-life of pesticides at varying pH values.
|Active ingredient||pH 6||pH 7||pH 8||pH 9|
|Azinphos-methyl||10 days||12 hours|
|Captan||8 hours||10 minutes||2 minutes|
|Carbaryl||100-150 days||24-30 days||2-3 days||1-3 days|
|Carbofuran||200 days||40 days||5 days||3 days|
|Chlorpyrifos||35 days||22 days|
|Diazinon||70 days||29 days|
|Dimethoate||12 hours||1 hour|
|Disulfoton||32 hours||7 hours|
|Malathion||8 days||3 days||19 hours|
|Methomyl||54 weeks||38 weeks||20 weeks|
|Phosmet||12-24 hours||4 hours|
|Parathion||17 weeks||29 days|
|Propargite||331 days||1 day|
|Trichlorfon||4 days||6 hours||1 hour|
Values are generalized estimates and may vary considerably depending upon factors other than pH.
Many water sources in Missouri have pH values between 7 and 9, or neutral to alkaline. There is some variability in these values even if they are within the same hydrologic region of the state. Both surface and ground water pH values fluctuate over time and even seasonally.
If you know that your mix water has a pH of 7.5 or greater, consider lowering the pH, especially if you are applying a pesticide that is sensitive to high pH. A pH of 4 to 7 is recommended for mixing most pesticides; a value of 5.5 to 6.5 is ideal.
If your spray rig will be left to stand for several hours or overnight before the contents are applied, consider adding a buffering agent to prevent alkaline hydrolysis.
The fastest way to determine the pH level of water is to test it with a pH meter or test paper. Paper test strips are the least expensive; however, they can be unreliable and vary by as much as 2 pH points. A pH meter will provide the most reliable and consistent readings. Meters are available commercially for $50 to $400.
More expensive models are extremely precise and may have the ability to conduct additional measurements such as electrical conductivity. The less expensive models usually have the capability to provide a pH reading within 0.1 to 0.2 points accuracy.
A final option is to have the water professionally monitored. The MU Soil and Plant Testing Laboratory conducts water pH analyses. Call 573-882-0623 for information and instructions on submitting samples or visit them on the Web at http://soilplantlab.missouri.edu/soil/. You can also submit samples through your county MU Extension center.
Product labels will direct you to avoid mixing the pesticide with alkaline water. You may also see statements that the activity of the pesticide will be reduced under alkaline conditions. The directions will state that a buffering or acidifying agent should be added to the spray tank. Some pesticidal materials should not be acidified under any circumstances; their labels will contain specific statements.
Buffering agents are a type of pesticide spray mix adjuvant. All adjuvant materials are added to the chemical formulation or spray tank to make the application more effective, safer or easier for the applicator.
Various commercially available buffering agents will acidify spray solution. Like pesticides, their labels should be read and followed closely. The amount to add will depend upon the initial pH, the volume of water, and the desired final results.
Determining the pH of the spray mix water and adding a buffering agent, if necessary, is inexpensive compared with the cost of losing a pesticide's effectiveness. Many of Missouri's water sources are alkaline by nature, and the addition of a buffering agent to the spray mix is an easy and economical way to guarantee maximum results from your pesticide applications.